2206 need help

6lat2012 · 2022-11-24T04:36:52.788Z

192.168.4.1

Syed · 2022-11-24T16:20:04.764Z

It looks like you have successfully connected to the UI. I think now you’ll need to point the LNB.

6lat2012 · 2022-11-24T18:09:35.271Z

Why is no working 10.0.0.1? (Skylark)

6lat2012 · 2022-11-24T18:13:16.926Z

166931354558761423646505051681131920×1440 398 KB

6lat2012 · 2022-11-26T04:27:36.156Z

Maybe wrong soft?

iw0hjz · 2022-11-26T14:53:17.728Z

Here it is

nice start of the day… the board is here… [othernet-1] [othernet-2] [othernet-3] [othernet2] [othernet1] easy with the same frequency ,same lnb. like the dark skin…is the SD necessary to store files? OK, thank a lot Sayed waiting tx from one of the board to the other ( ham license)

the ip addres is correct… then once in , go settings and put it on your net ( if you have one) …

6lat2012 · 2022-11-28T01:37:01.666Z

I can’t open 10.0.0.1

iw0hjz · 2022-11-28T10:14:13.553Z

you hav e a 2206 board… look:Dreamcatcher $99 - #47 by Syed

are you try to use skylark image with this board? for this board there is a github repository…above link.
hope this help

6lat2012 · 2022-12-04T01:14:16.361Z

Screenshot_20221203_1711391080×1666 123 KB

-8db signal good?

tylerhoot · 2022-12-04T01:34:23.829Z

good enough I am at -7 and don’t have any packet loss and that’s what you are trying to avoid which is packet loss. Cant remember what the min signal strength number required for it to receive data successfully.

6lat2012 · 2022-12-04T01:42:33.545Z

how long does it take to fully accept at least some file? 5 minutes, 2 hours? radio files will receive? aprs?

6lat2012 · 2023-01-12T22:07:44.651Z

Doesn’t save packages to memory card

Syed · 2023-01-13T19:21:52.519Z

According to the UI, how much space is available on the SD card?

6lat2012 · 2023-01-14T23:26:04.931Z

I used 32 and 8 gb.

Syed · 2023-01-15T16:59:58.496Z

Can you please take a screenshot of the available space on the SD card? This value is displayed in the UI.

Andre1 · 2023-02-25T17:51:03.923Z

Is there a way to switch the diseq port?
Need to switch the receiver to port 2.

Syed · 2023-02-27T17:02:17.145Z

I don’t understand. Could you please provide more details about the problem and your particular system?

Andre1 · 2023-02-27T17:21:11.620Z

I have a diseqc switch and port 1 has astra1 and port 2 has astra3.
So I have to switch on the receiver to port 2

caveman99 · 2023-02-27T21:48:16.592Z

The firmware can not do that yet, but the LNB driver can do it according to the datasheet. Should be as simple as sending the DISEqC B Position Select command.

6lat2012 · 2023-04-07T19:53:45.637Z

Screenshot_20230407_124702_My Files1079×1367 135 KB

Screenshot_20230407_124637_My Files1080×2400 126 KB

Device no save to sd card